Author Topic: Cleaning test tubes, what do you do? (Read 7738 times) 19 replies

Paddyc · « **on:** March 16, 2016, 09:05:35 PM »

As title, what do you guys do to clean out your test tubes (obviously aimed at those who own Liquid test kits.

I generally give the test tubes a good dousing under the running tap water, leave them to steep in hot water for a while then air dry standing on a paper towel...

I have started to notice my Ammonia test tube is yellowing and wonder what is the best and safest method to keep them crystal clean and sterile for tank use

Thanks in advance

Sue · « **Reply #1 on:** March 16, 2016, 09:17:09 PM »

After emptying the contents of the tube I fill it with water and empty it two or three times. Then half fill the tube, give it a good shake, then empty it three or four times. Then let it stand upside down in the sink for a few minutes while I wash any other tubes I've used. Then I wash the lids by holding them under a running tap.

Once I've finished all the washing I dry them in the same order. I get a clean paper hanky, hold it by one corner and twist it round to make a cylindrical shape which I then push down into the tube and twist round and round till the inside of the tube is dry. I use the other end of the hanky to dry the lid. You can do 2 tubes with one tissue.

I've found that leaving the tubes to stand full of tested water does leave a deposit on the inside of the tube. Using the paper hanky to dry them wipes any deposit off. If the tissue comes out very coloured, I wash and dry the tube again.

It has to be a paper hanky or possibly toilet paper as kitchen towels are too thick.

Paddyc · « **Reply #2 on:** March 16, 2016, 09:20:25 PM »

I'll give that a bash Sue, I kind of figured it's best to avoid chemical cleaners...

Sue · « **Reply #3 on:** March 16, 2016, 09:22:16 PM »

If you can find a test tube sized bottle brush, you could try that - carefully as the tubes are quite fragile. I recently twisted the top half off a tube trying to get the lid off.

Paddyc · « **Reply #4 on:** March 16, 2016, 09:25:53 PM »

Yeah I'm kind of thinking some Pyrex tubes might be an investment for the future. I intend to do regular testing... Probably at least twice weekly for the initial few months then down to weekly tests so they will get used a lot

Paddyc · « **Reply #5 on:** March 16, 2016, 10:02:32 PM »

EBay have plenty of sellers offering large packs of test tubes, 100 for £13 delivered, for example... If I bought a large amount I would happily pack them into half dozen lots and send them to you for a very small price, I could even include a 5ml syringe or two for no extra charge as I have access to plenty of them

Littlefish · « **Reply #6 on:** March 16, 2016, 10:06:38 PM »

I got a load of stuff off the internet, otherwise I wouldn't have been able to test all of the tanks on the same day.

Extreme_One · « **Reply #7 on:** March 16, 2016, 11:02:45 PM »

I have terrible habits I reckon.

After a test I rinse in tapwater and fill up and shake then empty and rinse a few more times. Then I store them back in the test kit. They're not even dried.

Then, before performing a new test I rinse them in tank water and empty and rinse a few times before collecting the tank water for the test.

I wouldn't recommend following my example.

BlindDogStanley · « **Reply #8 on:** March 17, 2016, 07:24:18 AM »

I'm afraid I just rinse them under the tap and put them back in the test kit box. Maybe I should be a little more fastidious in the cleaning of them?

fcmf · « **Reply #9 on:** March 17, 2016, 08:13:23 AM »

I just rinse several times, then put them onto a plastic tray in the fishkeeping cupboard, either on top of the aquarium sponge to drip into that or else tilted against it to dry out.

It might be possible to get rid of the yellowing that you describe by soaking them in sterilising solution such as Milton if you have any, but following that up with 24+ hours of soaking in water overdosed with dechlorinator, to get rid of any bleach residue. [Tip from Sue in the past for something else.]

Sue · « **Reply #10 on:** March 17, 2016, 10:51:42 AM »

I must admit that I've never bothered with the sterilising aspect, I just clean the tubes of any chemicals.

The method I use to clean them is the method we used to clean glassware in chemistry labs in the 1970s, except that we would rinse them in acetone as a last step. Some containers needed a very good scrubbing with a brush to get them clean! I haven't yet bought any test tube brushes as paper hankies seem to get the tubes clean enough.
I find that it's the nitrite test that stains my tubes most. But I have also found that they come clean easily if they are washed straight away after reading the result. It's when you leave them standing for hours that they get really stained.

Paddyc · « **Reply #11 on:** March 17, 2016, 10:19:13 PM »

I've been doing some brainstorming on this little issue for a few days. The API tubes I have just now seem rather fragile and I have heard of members breaking them accidentally during cleaning. The caps also do not always give a decent watertight seal when you shake the tube.

I'm seriously considering putting together a few kits of pyrex test tubes with blue push-caps (maybe 6) with a cleaning brush plus two syringes (one 6ml, one 25ml) and posting them to members who would like them? If there is enough interest I may well go ahead and bulk buy the test tubes and brushes at the end of the month. Let me know

Fiona · « **Reply #12 on:** March 17, 2016, 11:04:51 PM »

Quote from: Sue on March 16, 2016, 09:22:16 PM

carefully as the tubes are quite fragile.

Yup had to find replacement, I cut a tiny corner off a green scouring pad, stick it in the test tube and shake like billyho, so far its done the job, the key is drying them . It seems a pain in the bum because you're cycling. It gets simpler as the tank matures, I confess that I don't test my mature 200l more than once a fortnight now, unless I add new stock or fiddle with the planting. Smaller tanks need closer monitoring.

I'm cycling my shrimpery at the moment so I too have test tube pain

Extreme_One · « **Reply #13 on:** March 18, 2016, 07:43:30 AM »

Yes, I've noticed the same problems with the API tubes.

Quote from: Paddyc on March 17, 2016, 10:19:13 PM

I'm seriously considering putting together a few kits of pyrex test tubes with blue push-caps (maybe 6) with a cleaning brush plus two syringes (one 6ml, one 25ml) and posting them to members who would like them? If there is enough interest I may well go ahead and bulk buy the test tubes and brushes at the end of the month. Let me know

That sounds like a great idea. Especially if the kit includes a stand.

Let us know a price and I'll probably buy a set from you.

Paddyc · « **Reply #14 on:** March 18, 2016, 08:28:37 AM »

I was actually thinking about that too, Simon. I was thinking about making them out of either wood and/or metal. Shouldn't be much of a challenge

Fiona · « **Reply #15 on:** March 18, 2016, 11:07:54 AM »

I'd be interested Paddy, not the stand though, when they're dry I store mine in a tin

Anne · « **Reply #16 on:** March 18, 2016, 08:20:25 PM »

I'd be interested in test tubes and the stand as:

a. it doesn't look that easy to me to make (not in my skill set)
b. I am some what clumsy and have cracked several tubes by knocking them over

Anne

Paddyc · « **Reply #17 on:** March 18, 2016, 08:47:26 PM »

Quote from: Anne on March 18, 2016, 08:20:25 PM

I'd be interested in test tubes and the stand as:

a. it doesn't look that easy to me to make (not in my skill set)
b. I am some what clumsy and have cracked several tubes by knocking them over

Anne

The test tubes would be pyrex so less susceptible to cracking even when dropped... I have access to the materials so once I have some measurements and materials together I can start knocking out some kits. I've been thrown a bit of a fastball today and now need to find a new place to live so I'll see what I can achieve in the meantime, otherwise it will have to be after the move

Anne · « **Reply #18 on:** March 18, 2016, 08:55:24 PM »

Thanks, yes a house is much more important.

Good luck with the hunt.

Anne

Extreme_One · « **Reply #19 on:** March 18, 2016, 09:47:08 PM »

No hurry Paddy. Your home is far more important. Best of luck with that.

Subject - Started by	Replies	Last post
Glo T8 lighting tubes Started by Helen Fish Tanks and Equipment	4 Replies 6965 Views	January 29, 2013, 05:25:47 PM by ady81
Recommendations for blue/white LED lighting tubes please Started by Zo75 Fish Tanks and Equipment	5 Replies 8828 Views	August 08, 2013, 04:19:42 PM by Zo75
Test Kit Started by engineer_tom New Fishkeepers	3 Replies 8499 Views	September 07, 2013, 06:43:04 PM by Naomi12345
Light Tubes? Started by Resa Fish Tanks and Equipment	9 Replies 7514 Views	March 13, 2014, 12:50:28 PM by SteveS
Best test kit? Started by Loubaa General Fishkeeping advice	10 Replies 10771 Views	November 22, 2017, 09:01:50 AM by Sue
Changing light tubes Started by Richard W Fish Tanks and Equipment	2 Replies 5522 Views	May 11, 2015, 06:41:15 AM by Richard W
API master test kit - test tubes Started by Andys101 Fishtank Filtration and Cycling	10 Replies 17777 Views	January 13, 2017, 07:26:29 PM by Andys101

Cleaning Test Tubes, What Do You Do?

Cleaning Test Tubes, What Do You Do?

Author Topic: Cleaning test tubes, what do you do? (Read 7738 times) 19 replies

Assess Tankmates In The Tropical Fish Community Creator

Topics that relate to "Cleaning test tubes, what do you do?"

Tropical Fish Keeping Help and Advice

Tropical Fish Keeping Help and Advice

Tropical Fish Keeping Product Reviews

Tropical Fish Market Place

Tropical Fish Keeping Community